Machined aluminum free-float forends provides an exceptionally positive, non-slip gripping surface for the support hand to help ensure maximum weapon control. Easy-to-install, two-piece free-float design eliminates handguard stress on the barrel that can compromise accuracy. Use with rifle’s factory gas tube; if changing barrel length, purchase replacement gas tube of appropriate length. Rifle- and carbine-length models available in cobblestone-texture Overmolded™ rubber grasping surface.
SPECS: Forend – Aluminum, hardcoat anodized, matte black, with synthetic rubber covering on Overmolded models. Rifle - 12¼” (31.1cm) long, 2” (5cm) diameter. Fits AR-15/M16 and clones with rifle-length gas system. Carbine – 7-1⁄8” (17.8cm) long, 2” diameter. Fits AR-15/M16/M4 and clones with carbine-length gas system.
Altro...
Superficie di Presa Confortevole e Antiscivolo
Forend in alluminio lavorato a macchina e free-float, fornisce una superficie di presa eccezionalmente positiva e antiscivolo per la mano di supporto per aiutare a garantire il massimo controllo dell'arma. Facile da installare, il design free-float in due pezzi elimina lo stress del handguard sul canna che può compromettere la precisione. Utilizzare con il tubo del gas di fabbrica del fucile; se si cambia la lunghezza della canna, acquistare un tubo del gas di lunghezza appropriata. Modelli disponibili per lunghezza da fucile e da carabina con superficie di presa in gomma Overmolded™ con texture a ciottoli.
SPECIFICHE: Forend – Alluminio, anodizzato hardcoat, nero opaco, con rivestimento in gomma sintetica sui modelli Overmolded. Rifle - 12¼” (31.1cm) di lunghezza, 2” (5cm) di diametro. Adatto per AR-15/M16 e cloni con sistema a gas di lunghezza da fucile. Carbine – 7-1⁄8” (17.8cm) di lunghezza, 2” di diametro. Adatto per AR-15/M16/M4 e cloni con sistema a gas di lunghezza da carabina.
Altro...
Punteggi dei clienti per HOGUE RIFLE FOREND, OVERMOLDED
Numero di punteggi: 7
Da brownells.com: 7
Punteggio medio: 2,9
Lucky if you get one that fits(20/02/2016)
Typically, you would think Hogue makes some solid, comfortable products. Well, this one is quite solid. So solid it won't fit. If you look at the instructions, it'll say you should note the alignment of the gas tube port on the upper receiver with one of the many available gas tube holes around the barrel nut when hand tightened, then tighten it to the next hole, which is anywhere from 1/2 of a notch to a notch and a half. Well, I was lucky enough to score myself on the halfway mark. I lubed up the sucker quite copiously. I then hand tightened it to line up perfect with one of the holes on the barrel nut. Of course, that's not going to fly (or will it just fly off?), so I took out the supplied wrench and noticed it won't fit. It's not the right size. The 2" end of the wrench is too small. The 2 1/8" side is too big. OK, great. Fortunately I have a strap wrench handy. I'll take that and tighten it. Well... that didn't work either. I got halfway there, muscled it, and now I feel Hogue owes me a new strap wrench because I tore mine up. Despite my best efforts, the gas tube won't go in because the hole is completely misaligned. How Hogue expects you to tighten it a whole notch, let alone one and a half, is beyond me.
Bottom line: this is a piece of junk. You'll notice in another review of a similar Hogue hand guard that the reviewer suffered a similar issue. Clearly I'm not the only one. I typically don't write scathing reviews, but I feel like I have to put out a PSA on this for humankind. So here goes: If you are a decent human being, do not buy this product.
Would not buy again(14/09/2012)
The pins on my barrel wrench were not long enough to engage into the barrel nut. The directions gave instruction on how to modify your gas tube-meanwhile the description block on the website said that modification of the tube was not required. I didn't want to modify my gas tube. The grip handle didn't come with the package, evidently that is sold separately.
Great forend with Hogue 3-gun extention(29/09/2012)
This is a super short forend for carbine Ar15 rifles. If you use Hogue's "3gun" extention with this forend, you get a perfect 15" length forend on a 18-20" Ar rifle, and have the rubber grip out where you need it. I have this setup on 2 of my guns and they look and work fantastic.
Not worth the trouble or money(09/10/2013)
This has got to be the worst engineered product I have bought in quite a while. I understand that you have to pay sixty plus dollars for an aluminum tube, but then they tell you that you will have to bend your gas tube an advise you get a gunsmith to do it for ( $65-$100 dollars an hour). Lastly the barrel nut needs a strap wrench or as they advise get an old belt and a pair of vice grips to put in on. I guest just get it tight is good enough, not to worry about torquing it down.
Horrible(29/12/2017)
Just finished installing this total piece of junk on a buddy's gun. The wrench they give you is a joke and you have to buy a special gas tube or mess with bending the existing one. I have install many many handguards and this is the WORST one I have ever used.
Easy to install free float forend(26/01/2010)
Installed this forend on my Armalite 16" midlength gas system and was really glad I did. Clean lines, full free float, hogue pebble grip surface. The only down side is that you have to drill and tap for a bipod stud.
Hogue hits home run!(04/02/2015)
I did my first install of a hogue free float tube today and was very happy with it. I will say that reading the included instructions prior to starting was very helpful as they were very clear and tell you what you need to know before you make a mistake. The included wrench is less complicated than it sounds. Very nice product, well made, very sturdy. I will be using this product on my next AR-15 build, parts should be here soon. Both rifles are for target/varmint shooting.
N. prodotto: 408150020 HOGUE RIFLE FOREND, OVERMOLDED Parti Fabbricante: 15004743108150047 Forend in alluminio lavorato a macchina e free-float, fornisce una superficie di presa eccezionalmente positiva e antiscivolo per la mano di supporto per aiutare a garantire il massimo controllo dell'arma. Facile da installare, il design free-float in due pezzi elimina lo stress del handguard sul canna che può compromettere la precisione. Utilizzare con il tubo del gas di fabbrica del fucile; se si cambia la lunghezza della canna, acquistare un tubo del gas di lunghezza appropriata. Modelli disponibili per lunghezza da fucile e da carabina con superficie di presa in gomma Overmolded™ con texture a ciottoli.
Forend flottante in alluminio anodizzato con rivestimento in gomma Overmolded™ per una presa antiscivolo e massimo controllo dell'arma.
Facile da installare, il design free-float in due pezzi elimina lo stress sul canna, migliorando la precisione.
Disponibile in due lunghezze: 12¼” per fucili e 7-1⁄8” per carabine, adatto per AR-15/M16/M4 e cloni.
Caratteristiche
Adatto per:
AR-15
Colore:
Nero
Lunghezza:
12
Materiale:
Alluminio
Tipo:
Flottante
Peso della spedizione: 0,431kgAltezza di spedizione: 5mmLarghezza di spedizione: 150mmLunghezza di spedizione: 358mm
UPC
: 743108150047
Dettagli dell'elemento
Classificazione per l'export dagli US: 0A501.y.1
Questi articoli sono controllati dal governo degli Stati Uniti e ne è autorizzata l'esportazione solo nel paese di destinazione finale e l'uso solo da parte del destinatario finale o degli utenti finali qui identificati. Questi beni non possono essere rivenduti, trasferiti o altrimenti ceduti a nessun altro paese o a persone diverse dal destinatario finale o dall'utente finale autorizzati, nella loro forma originale o dopo essere stati incorporati in altri articoli, senza prima ottenere l'approvazione dal governo degli Stati Uniti o come altrimenti autorizzato dalla legge e dai regolamenti degli Stati Uniti.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Operatore economico responsabile secondo il regolamento UE
Brownells
Via Mezzavilla 4
25043 Breno
Italia
service@brownells.it
N. prodotto: 408150120 HOGUE CARBINE FOREND, OVERMOLDED Parti Fabbricante: 15014743108150122 Forend in alluminio lavorato a macchina e free-float, fornisce una superficie di presa eccezionalmente positiva e antiscivolo per la mano di supporto per aiutare a garantire il massimo controllo dell'arma. Facile da installare, il design free-float in due pezzi elimina lo stress del handguard sul canna che può compromettere la precisione. Utilizzare con il tubo del gas di fabbrica del fucile; se si cambia la lunghezza della canna, acquistare un tubo del gas di lunghezza appropriata. Modelli disponibili per lunghezza da fucile e da carabina con superficie di presa in gomma Overmolded™ con texture a ciottoli.
Il forend HOGUE per carabine AR-15 è realizzato in alluminio lavorato a macchina, con un design free-float in due pezzi che migliora la precisione eliminando lo stress sul canna.
La superficie di presa in gomma Overmolded™ con texture a ciottoli garantisce un controllo eccezionale e antiscivolo dell'arma.
Compatibile con sistemi a gas di lunghezza da carabina, è facile da installare e disponibile in colore nero opaco con rivestimento in gomma sintetica.
Caratteristiche
Adatto per:
AR-15
Colore:
Nero
Lunghezza:
7
Materiale:
Alluminio
Tipo:
Carbine,Flottante
Peso della spedizione: 0,295kgAltezza di spedizione: 36mmLarghezza di spedizione: 152mmLunghezza di spedizione: 358mm
UPC
: 743108150122
Dettagli dell'elemento
Classificazione per l'export dagli US: 0A501.y.1
Questi articoli sono controllati dal governo degli Stati Uniti e ne è autorizzata l'esportazione solo nel paese di destinazione finale e l'uso solo da parte del destinatario finale o degli utenti finali qui identificati. Questi beni non possono essere rivenduti, trasferiti o altrimenti ceduti a nessun altro paese o a persone diverse dal destinatario finale o dall'utente finale autorizzati, nella loro forma originale o dopo essere stati incorporati in altri articoli, senza prima ottenere l'approvazione dal governo degli Stati Uniti o come altrimenti autorizzato dalla legge e dai regolamenti degli Stati Uniti.
This item is controlled by the U.S. government and authorized for export only to the country of ultimate destination for use by the ultimate consignee or end-user(s) herein identified. It may not be resold, transferred, or otherwise disposed of, to any other country or to any person other than the authorized ultimate consignee or end-user(s), either in their original form or after being incorporated into other items, without first obtaining approval from the U.S. government or as otherwise authorized by U.S. law and regulations.
Operatore economico responsabile secondo il regolamento UE
Brownells
Via Mezzavilla 4
25043 Breno
Italia
service@brownells.it
Scopri il forend HOGUE per AR-15! ✨ Design free-float in alluminio per un controllo ottimale e precisione. Facile da installare!
Machined aluminum free-float forends provides an exceptionally positive, non-slip gripping surface for the support hand to help ensure maximum weapon control. Easy-to-install, two-piece free-float design eliminates handguard stress on the barrel that can compromise accuracy. Use with rifle’s factory gas tube; if changing barrel length, purchase replacement gas tube of appropriate length. Rifle- and carbine-length models available in cobblestone-texture Overmolded™ rubber grasping surface.
SPECS: Forend – Aluminum, hardcoat anodized, matte black, with synthetic rubber covering on Overmolded models. Rifle - 12¼” (31.1cm) long, 2” (5cm) diameter. Fits AR-15/M16 and clones with rifle-length gas system. Carbine – 7-1⁄8” (17.8cm) long, 2” diameter. Fits AR-15/M16/M4 and clones with carbine-length gas system.
Altro...
Superficie di Presa Confortevole e Antiscivolo
Forend in alluminio lavorato a macchina e free-float, fornisce una superficie di presa eccezionalmente positiva e antiscivolo per la mano di supporto per aiutare a garantire il massimo controllo dell'arma. Facile da installare, il design free-float in due pezzi elimina lo stress del handguard sul canna che può compromettere la precisione. Utilizzare con il tubo del gas di fabbrica del fucile; se si cambia la lunghezza della canna, acquistare un tubo del gas di lunghezza appropriata. Modelli disponibili per lunghezza da fucile e da carabina con superficie di presa in gomma Overmolded™ con texture a ciottoli.
SPECIFICHE: Forend – Alluminio, anodizzato hardcoat, nero opaco, con rivestimento in gomma sintetica sui modelli Overmolded. Rifle - 12¼” (31.1cm) di lunghezza, 2” (5cm) di diametro. Adatto per AR-15/M16 e cloni con sistema a gas di lunghezza da fucile. Carbine – 7-1⁄8” (17.8cm) di lunghezza, 2” di diametro. Adatto per AR-15/M16/M4 e cloni con sistema a gas di lunghezza da carabina.
Altro...
Punteggi dei clienti per HOGUE RIFLE FOREND, OVERMOLDED
Numero di punteggi: 7
Da brownells.com: 7
Punteggio medio: 2,9
Lucky if you get one that fits(20/02/2016)
Typically, you would think Hogue makes some solid, comfortable products. Well, this one is quite solid. So solid it won't fit. If you look at the instructions, it'll say you should note the alignment of the gas tube port on the upper receiver with one of the many available gas tube holes around the barrel nut when hand tightened, then tighten it to the next hole, which is anywhere from 1/2 of a notch to a notch and a half. Well, I was lucky enough to score myself on the halfway mark. I lubed up the sucker quite copiously. I then hand tightened it to line up perfect with one of the holes on the barrel nut. Of course, that's not going to fly (or will it just fly off?), so I took out the supplied wrench and noticed it won't fit. It's not the right size. The 2" end of the wrench is too small. The 2 1/8" side is too big. OK, great. Fortunately I have a strap wrench handy. I'll take that and tighten it. Well... that didn't work either. I got halfway there, muscled it, and now I feel Hogue owes me a new strap wrench because I tore mine up. Despite my best efforts, the gas tube won't go in because the hole is completely misaligned. How Hogue expects you to tighten it a whole notch, let alone one and a half, is beyond me.
Bottom line: this is a piece of junk. You'll notice in another review of a similar Hogue hand guard that the reviewer suffered a similar issue. Clearly I'm not the only one. I typically don't write scathing reviews, but I feel like I have to put out a PSA on this for humankind. So here goes: If you are a decent human being, do not buy this product.
Would not buy again(14/09/2012)
The pins on my barrel wrench were not long enough to engage into the barrel nut. The directions gave instruction on how to modify your gas tube-meanwhile the description block on the website said that modification of the tube was not required. I didn't want to modify my gas tube. The grip handle didn't come with the package, evidently that is sold separately.
Great forend with Hogue 3-gun extention(29/09/2012)
This is a super short forend for carbine Ar15 rifles. If you use Hogue's "3gun" extention with this forend, you get a perfect 15" length forend on a 18-20" Ar rifle, and have the rubber grip out where you need it. I have this setup on 2 of my guns and they look and work fantastic.
Not worth the trouble or money(09/10/2013)
This has got to be the worst engineered product I have bought in quite a while. I understand that you have to pay sixty plus dollars for an aluminum tube, but then they tell you that you will have to bend your gas tube an advise you get a gunsmith to do it for ( $65-$100 dollars an hour). Lastly the barrel nut needs a strap wrench or as they advise get an old belt and a pair of vice grips to put in on. I guest just get it tight is good enough, not to worry about torquing it down.
Horrible(29/12/2017)
Just finished installing this total piece of junk on a buddy's gun. The wrench they give you is a joke and you have to buy a special gas tube or mess with bending the existing one. I have install many many handguards and this is the WORST one I have ever used.
Easy to install free float forend(26/01/2010)
Installed this forend on my Armalite 16" midlength gas system and was really glad I did. Clean lines, full free float, hogue pebble grip surface. The only down side is that you have to drill and tap for a bipod stud.
Hogue hits home run!(04/02/2015)
I did my first install of a hogue free float tube today and was very happy with it. I will say that reading the included instructions prior to starting was very helpful as they were very clear and tell you what you need to know before you make a mistake. The included wrench is less complicated than it sounds. Very nice product, well made, very sturdy. I will be using this product on my next AR-15 build, parts should be here soon. Both rifles are for target/varmint shooting.