Helps prevent dinged and damaged scope tubes by removing high spots to quickly true misaligned or out-of-round scope rings so they're perfectly in line. Also works to turn-in and rough align rotary dovetail rings. Dual-handles with multiple, transverse, lapping compound grooves give complete control and fast results. Includes lapping compound.
SPECS: Mild steel, in-the-white. 12" (30cm) long, 1" (2.5cm) or 30mm (1.187") dia. Includes (2) plastic handles and instructions.
Altro...
Allinea gli Anelli del Cannocchiale; Previene Danni
Aiuta a prevenire ammaccature e danneggiamenti dei tubi del cannocchiale rimuovendo le irregolarità per allineare rapidamente gli anelli del cannocchiale disallineati o non perfettamente rotondi cosicché siano perfettamente in linea. Funziona anche per allineare grossolanamente e montare gli anelli a coda di rondine rotativi. Doppie maniglie con molteplici scanalature trasversali per la pasta abrasiva offrono controllo completo e risultati rapidi. Include la pasta abrasiva.
SPECIFICHE: Acciaio dolce, grezzo. Lunghezza 12" (30 cm), diametro 1" (2,5 cm) o 30 mm (1,187"). Include (2) maniglie in plastica e istruzioni.
Altro...
Punteggi dei clienti per BROWNELLS 30MM SCOPE RING ALIGNMENT LAP
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 3,8
30MM lapping bar(04/04/2010)
I used this 30 MM lapping bar for the rings on a new NF 8X32. It worked great. at start I had .020 gap on both sides of the rings with hard points on rear of both sets. After lapping, I had over 80% contact with tube and just onder .010 gap at ring split lines. I now have a 1" lapping bar to go with this one.
Everyone should have one of these!(30/12/2011)
I don't think you can get any better quality in a lapping tool. This thing is solid steel and very heavy duty. The multiple handle attachment points are very nice as well. This item comes with the 800 grit lapping compound which worked very well but took awhile to get full 80% contact on the rings. I would recommend purchasing the 600 grit compound separately to speed the process up a little bit or buy an extra six pack of beer. Overall I am very satisfied with my purchase and will be purchasing a 1" model to go with this one.... and some extra 600 grit compound.
disappointed...(24/03/2015)
it's just a piece of 1 3/16 raw cold rolled bar. The lapping surface is not machined. Mine spec'd out at 30.06>30.12 I didnt even bother to check the run out. I measured all my 30mm scopes and they were all 29.95 and mounted in Mark4 steel rings that this bar will never touch
A better product than cheaper versions(24/11/2010)
Unlike cheaper versions from other suppliers, this lap has grooves for carrying lapping compound. It also has multiple handle attachment points, which is important when working rings that are very close together (or very far apart), or when the structure of the firearm only allows access from certain positions.
A few quick passes will let you know whether you're close ... and to keep going ... or you're not, in which case you may need a reamer (such as the one from Clymer) or perhaps a new set of rings.
N. prodotto: 080903130 BROWNELLS 30MM SCOPE RING ALIGNMENT LAP050806026834 Aiuta a prevenire ammaccature e danneggiamenti dei tubi del cannocchiale rimuovendo le irregolarità per allineare rapidamente gli anelli del cannocchiale disallineati o non perfettamente rotondi cosicché siano perfettamente in linea. Funziona anche per allineare grossolanamente e montare gli anelli a coda di rondine rotativi. Doppie maniglie con molteplici scanalature trasversali per la pasta abrasiva offrono controllo completo e risultati rapidi. Include la pasta abrasiva.
104.9EUR0104,90 €
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Il SCOPE RING ALIGNMENT LAP di BROWNELLS aiuta a prevenire ammaccature e danni ai tubi del cannocchiale allineando rapidamente gli anelli disallineati.
Le doppie maniglie con scanalature trasversali per la pasta abrasiva offrono controllo completo e risultati rapidi; include la pasta abrasiva.
Specifiche: acciaio dolce, lunghezza 12" (30 cm), diametro 30 mm (1,187"), include (2) maniglie in plastica e istruzioni.
Caratteristiche
Peso della spedizione: 1,905kgAltezza di spedizione: 74mmLarghezza di spedizione: 91mmLunghezza di spedizione: 411mm
UPC
: 050806026834
Dettagli dell'elemento
Made in Usa
Operatore economico responsabile secondo il regolamento UE
Brownells
Via Mezzavilla 4
25043 Breno
Italia
service@brownells.it
N. prodotto: 080903100 BROWNELLS 1" SCOPE RING ALIGNMENT LAP050806026827 Aiuta a prevenire ammaccature e danneggiamenti dei tubi del cannocchiale rimuovendo le irregolarità per allineare rapidamente gli anelli del cannocchiale disallineati o non perfettamente rotondi cosicché siano perfettamente in linea. Funziona anche per allineare grossolanamente e montare gli anelli a coda di rondine rotativi. Doppie maniglie con molteplici scanalature trasversali per la pasta abrasiva offrono controllo completo e risultati rapidi. Include la pasta abrasiva.
94.9EUR094,90 €
*
In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.
Helps prevent dinged and damaged scope tubes by removing high spots to quickly true misaligned or out-of-round scope rings so they're perfectly in line. Also works to turn-in and rough align rotary dovetail rings. Dual-handles with multiple, transverse, lapping compound grooves give complete control and fast results. Includes lapping compound.
SPECS: Mild steel, in-the-white. 12" (30cm) long, 1" (2.5cm) or 30mm (1.187") dia. Includes (2) plastic handles and instructions.
Altro...
Allinea gli Anelli del Cannocchiale; Previene Danni
Aiuta a prevenire ammaccature e danneggiamenti dei tubi del cannocchiale rimuovendo le irregolarità per allineare rapidamente gli anelli del cannocchiale disallineati o non perfettamente rotondi cosicché siano perfettamente in linea. Funziona anche per allineare grossolanamente e montare gli anelli a coda di rondine rotativi. Doppie maniglie con molteplici scanalature trasversali per la pasta abrasiva offrono controllo completo e risultati rapidi. Include la pasta abrasiva.
SPECIFICHE: Acciaio dolce, grezzo. Lunghezza 12" (30 cm), diametro 1" (2,5 cm) o 30 mm (1,187"). Include (2) maniglie in plastica e istruzioni.
Altro...
Punteggi dei clienti per BROWNELLS 30MM SCOPE RING ALIGNMENT LAP
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 3,8
30MM lapping bar(04/04/2010)
I used this 30 MM lapping bar for the rings on a new NF 8X32. It worked great. at start I had .020 gap on both sides of the rings with hard points on rear of both sets. After lapping, I had over 80% contact with tube and just onder .010 gap at ring split lines. I now have a 1" lapping bar to go with this one.
Everyone should have one of these!(30/12/2011)
I don't think you can get any better quality in a lapping tool. This thing is solid steel and very heavy duty. The multiple handle attachment points are very nice as well. This item comes with the 800 grit lapping compound which worked very well but took awhile to get full 80% contact on the rings. I would recommend purchasing the 600 grit compound separately to speed the process up a little bit or buy an extra six pack of beer. Overall I am very satisfied with my purchase and will be purchasing a 1" model to go with this one.... and some extra 600 grit compound.
disappointed...(24/03/2015)
it's just a piece of 1 3/16 raw cold rolled bar. The lapping surface is not machined. Mine spec'd out at 30.06>30.12 I didnt even bother to check the run out. I measured all my 30mm scopes and they were all 29.95 and mounted in Mark4 steel rings that this bar will never touch
A better product than cheaper versions(24/11/2010)
Unlike cheaper versions from other suppliers, this lap has grooves for carrying lapping compound. It also has multiple handle attachment points, which is important when working rings that are very close together (or very far apart), or when the structure of the firearm only allows access from certain positions.
A few quick passes will let you know whether you're close ... and to keep going ... or you're not, in which case you may need a reamer (such as the one from Clymer) or perhaps a new set of rings.