Il Carrello è vuoto.

Carrello

Aiuto e contatti

Reso facile

Newsletter

Offerte

Oltre 300.000 clienti - vi ringraziamo!

4,93/5 "Molto buono" (1400+ recensioni)

Oltre 40.000 prodotti per caccia e sport di tiro

WILLIAMS GUN SIGHT
MARLIN DOVETAIL FIRE SIGHT SET

053506602179 962602170

Upgrade Your Factory Sights With Easy-To-See, Fiber Optics

All sets feature a bright red, fiber optic, front sight and fully adjustable peep or U-notch, rear sight. U-notch, rear sight sets use the highly accurate, 3-dot pattern with two green, fiber optic dots at the rear for sharp contrast and quick sight acquisition in all light conditions. No drilling or tapping required for most rifle models. Dovetailed front and rear sights may require minor fitting. For Marlin and Winchester lever action rifles. Dovetail replaces factory front and rear sights. Rear sight is screw adjustable for elevation and drift adjustable for windage; has two, green, fiber optic dots. Front has red, fiber optic rod.

SPECS: Aluminum, black anodized. Dovetail fits all Winchester and Marlin lever actions with ramped front sights. FP-94/36 fits Win. 94 top eject and models 55, 63, 64, and 65; Marlin 36, 336, 1894, 1895 and 444. Will not fit Win. 94/22. Requires two holes in the left side of the receiver and will require drilling and tapping on the newer guns. FP-94SE fits Win. 94 angle eject with front ramp, except Big Bore models. FP-336 fits Marlin 36, 336, 1894, 1895 and 444. Attaches to the top of the receiver and bolts up to factory drilled and tapped holes. FP-450 fits Marlin 450. WGRS-336 fits Marlin 336, 444, 44 and 1895. 5D-94 fits Winchester 94 top eject rifles. 5D-336 fits Marlin 336 rifles, mounts using scope mount holes.

Altro...

Migliora le tue mire di fabbrica con le mire a fibra ottica facili da vedere

Tutti i set includono una mira anteriore luminosa a fibra ottica rossa e una mira posteriore completamente regolabile a foro o a tacca a U. I set con mira posteriore a tacca a U utilizzano il preciso schema a 3 punti con due punti in fibra ottica verdi posteriori per un contrasto nitido e un rapido acquisizione della mira in tutte le condizioni di luce. Non è necessario forare o maschiare per la maggior parte dei modelli di fucili. Le mire anteriori e posteriori a coda di rondine possono richiedere una leggera modifica. Per fucili a leva Marlin e Winchester. La coda di rondine sostituisce le mire anteriori e posteriori di fabbrica. La mira posteriore è regolabile in altezza con vite e regolabile in deriva; ha due punti in fibra ottica verdi. La parte anteriore ha una bacchetta in fibra ottica rossa.

SPECIFICHE: Alluminio, anodizzato nero. Il Dovetail si adatta a tutte le azioni a leva Winchester e Marlin con mire anteriori rampate. Il FP-94/36 si adatta a Win. 94 espulsione superiore e modelli 55, 63, 64 e 65; Marlin 36, 336, 1894, 1895 e 444. Non compatibile con Win. 94/22. Richiede due fori sul lato sinistro del ricevitore e necessiterà di foratura e maschiatura sulle armi più recenti. Il FP-94SE si adatta a Win. 94 espulsione angolare con rampa anteriore, esclusi i modelli Big Bore. Il FP-336 si adatta a Marlin 36, 336, 1894, 1895 e 444. Si attacca alla parte superiore del ricevitore e si fissa ai fori preesistenti forati e maschiati. Il FP-450 si adatta a Marlin 450. Il WGRS-336 si adatta a Marlin 336, 444, 44 e 1895. Il 5D-94 si adatta ai fucili Winchester 94 con espulsione superiore. Il 5D-336 si adatta ai fucili Marlin 336, si monta utilizzando i fori per il montaggio dell'ottica.

Altro...

Punteggi dei clienti per WILLIAMS GUN SIGHT MARLIN FIBER OPTIC DOVETAIL FIRE SIGHT SET MULTI

Numero di punteggi: 13
Da brownells.com: 13
Punteggio medio: 2,7

Winchester Model 94 XTR Chambered in 375 (27/01/2010)

I installed the dovetail sight set and was thrilled with the sight picture; the fiber optics really make sight acquisition easy. However, no joy when I took the rifle to the range. I couldn't hit the target at 25 steps...too high. After adjusting the rear sight as low as it would go (i.e. removed the set screw), I just did hit the top of the box to which I had placed a shoot-n-see target. I guess the only option is to raise the front sight, and this will be nothing but a snag in the gun case.

Easy,bright sight (12/06/2010)

Put these sights on a MArlin 1895 Cuide Gun with the ported barrel. Very easy to install and the sight picture is much better than the stock sight. I shoot hot hand loads and sighting in at 100 yards I had to crank the rear sight almost to the very top of the adjustment screw. I will be buying another set for a different 45-70 rifle I have.

Excellent inexpensive sight. (06/12/2010)

I put a set of these on my 1895 45-70 and 1894 44 mag Marlins. The 1895 install corrected a problem the factory sights had, shooting 5" low. The sight set comes with an M type front insert, but the 1894 requires an N width of the same height #34. It is very common to have to juggle front sight insert height on different lever guns chambered for different cartridges, 0.009" per inch of shift at 50 yards.

Sight picture is excellent, sights are highly visible and it is nice to have simple windage adjustment.

Not enough adjustment available (09/04/2011)

Tried it on a Marlin 336 and a Winchester model 94. Sight picture and visibility is great! Unfortunately, there's not enough adjustment to get either one of these rifles to hit paper. The front and rear sight heights are made way too far off from each other to get the elevation adjusted correctly. I had to go back to the original sights.

Good Speed Sights (21/06/2012)

Installed on Marlin 1894. As mentioned in GunTech article, also order the the .312 N front blade which fits Marlin better. With rear all the way down and using .312 front, able to tear up the target center at 25 yds. at speed.

Big improvement over factory sights. (09/08/2012)

Needed minor fitting (filing) of the front sight. Rear sight was an easy swap. Took about 30 minutes to install both. Makes for a quick sight picture. Easy to adjust- will need a very small screwdriver to do so. Makes my Marlin 1895G much easier for me to shoot accurately.

Didn't Work (24/09/2012)

Great low light visibility. Installed a set on my Winchester 94 in 356. Shoots 16" high @ 100 meters with rear sight all the way down. Judging by other's comments this is a common scenario. Wish Williams wouldn't have advertised it for this gun. I would have saved myself a lot of time.

not for a marlin 336 (13/06/2013)

Rear sight was easy to install, Front sight took some machining to clear the barrel band. With the rear sight at the lowest setting the gun was 2 feet high at 25 yards. Wasted time and money. Expected more from a williams product.

great sights (29/06/2013)

Well I don't know about other lever guns but they fit my Marlin 1895 guide gun with no issues. I just filed the front sight until it fit like the old one and now it looks like it came that way. Took it out to the range and it sighted in nice and easy.

good for the money (27/12/2013)

good for low light hunting

good sights for Win 94/22M (15/08/2014)

Installed on a 30 yr old Winchester 94/22 in 22M. First shot on the bull at 15yds. A little low at 100. sight picture is incredible good product.

Not for a Marlin 336 (22/02/2016)

I agree with the pervious comment by Earl. I installed these sights om a Marlin 336. Installation was fairly straightforward.

But the rifle shoots 16 inches high at 50 yards. This may fit a variety of rifles, but it just does not work on a 336. Wasted money

gun shoots over 12 high at 100 yds now (09/04/2017)

front sight to low for Winchester 94

Leggi più recensioni su brownells.com

84.9 84.9 1 EUR

N. prodotto: 962602170
WILLIAMS GUN SIGHT MARLIN FIBER OPTIC DOVETAIL FIRE SIGHT SET MULTI
Parti Fabbricante: 60217 053506602179 Tutti i set includono una mira anteriore luminosa a fibra ottica rossa e una mira posteriore completamente regolabile a foro o a tacca a U. I set con mira posteriore a tacca a U utilizzano il preciso schema a 3 punti con due punti in fibra ottica verdi posteriori per un contrasto nitido e un rapido acquisizione della mira in tutte le condizioni di luce. Non è necessario forare o maschiare per la maggior parte dei modelli di fucili. Le mire anteriori e posteriori a coda di rondine possono richiedere una leggera modifica. Per fucili a leva Marlin e Winchester. La coda di rondine sostituisce le mire anteriori e posteriori di fabbrica. La mira posteriore è regolabile in altezza con vite e regolabile in deriva; ha due punti in fibra ottica verdi. La parte anteriore ha una bacchetta in fibra ottica rossa.

84.9 EUR 0 84,90 € *

In arretrato, tempi di consegna circa 4-12 settimane dal magazzino negli Stati Uniti.

Caratteristiche: Adatto per: Marlin, Winchester Colore: Multi Colore delle mire: Red/Green Modello: Universal Rifles Tipo: Fibra ottica

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Top takeaways

Il set include una mira anteriore in fibra ottica rossa e una mira posteriore regolabile con due punti verdi per un'acquisizione rapida della mira.
Adatto per fucili a leva Marlin e Winchester, la coda di rondine sostituisce le mire di fabbrica senza necessità di foratura per la maggior parte dei modelli.
Realizzato in alluminio anodizzato nero, il set è compatibile con vari modelli come Marlin 36, 336, 1894, 1895 e Winchester 94, con alcune eccezioni.

Caratteristiche

Adatto per: Marlin,Winchester Colore: Multi Colore delle mire: Red/Green Modello: Universal Rifles Tipo: Fibra ottica Peso della spedizione: 0,032kg Altezza di spedizione: 8mm Larghezza di spedizione: 99mm Lunghezza di spedizione: 152mm UPC : 053506602179