Contains one reduced power trigger spring and one disconnector spring Designed to lighten and improve trigger function For use in AR15, M16, M4, & variants
Altro...
Contiene una molla del grilletto a potenza ridotta e una molla del disconnettore progettate per alleggerire e migliorare la funzione del grilletto. Da utilizzare in AR15, M16, M4 e varianti
Altro...
Punteggi dei clienti per WOLFF AR15/M16 TRIGGER FUNCTION PAK
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 3
Don't buy this product(28/09/2013)
I installed these springs in my Bushmaster AR-15. Before installation my trigger pull was 7.52 lbs. After spring change trigger pull was still about the same. Instalation was very easy though.
Excellent product(23/12/2013)
I've used two sets of these springs and they make a very noticeable light and smooth difference in my two ar15s. I will be ordering several more.
Save the money(06/05/2017)
I have used a lot of Wolff springs, but always in cowboy shooting guns. Some made a lot of difference, some a little, while others could be made equally well with original parts and some tuning.
This is one case to just save your money, as little as they cost to begin with. Actually, save yourself the aggravation of R&R the hammer spring just to get to this.
I took seven readings before doing a thing. They varied from7.5 to 6.75 lbs of pull; mostly 7.5. After going through the whole mess, then lubing everything again, I got the same readings. Mostly 7.5 lbs. What a disappointment!!
The worst part of it all is that this was replacing a spring out of a DPMS lower parts kit, so pretty bottom of the barrel to begin with.
OTOH, the included disconnector spring seems to tighter. It is definitely a little shorter though; not by much.
Good bang for the buck(02/07/2017)
Have used these on a few lowers. I start out with a Critical Capabilities LPK with ELG trigger. Pull weight is reduced and with some polishing on the trigger and hammer engagement surfaces I was able to get a very nice smooth pull between 4.5 and 6 lbs, (avg 5.25 lbs) with no loss of reliability on hard primers.,
N. prodotto: 969000244 WOLFF AR15/M16 TRIGGER FUNCTION PAK Parti Fabbricante: 34910 Contiene una molla del grilletto a potenza ridotta e una molla del disconnettore progettate per alleggerire e migliorare la funzione del grilletto. Da utilizzare in AR15, M16, M4 e varianti
24.9EUR1824,90 €
*
Tempi di consegna circa 12-16 giorni. Più di 10 pz. nel magazzino USA
Contains one reduced power trigger spring and one disconnector spring Designed to lighten and improve trigger function For use in AR15, M16, M4, & variants
Altro...
Contiene una molla del grilletto a potenza ridotta e una molla del disconnettore progettate per alleggerire e migliorare la funzione del grilletto. Da utilizzare in AR15, M16, M4 e varianti
Altro...
Punteggi dei clienti per WOLFF AR15/M16 TRIGGER FUNCTION PAK
Numero di punteggi: 4
Da brownells.com: 4
Punteggio medio: 3
Don't buy this product(28/09/2013)
I installed these springs in my Bushmaster AR-15. Before installation my trigger pull was 7.52 lbs. After spring change trigger pull was still about the same. Instalation was very easy though.
Excellent product(23/12/2013)
I've used two sets of these springs and they make a very noticeable light and smooth difference in my two ar15s. I will be ordering several more.
Save the money(06/05/2017)
I have used a lot of Wolff springs, but always in cowboy shooting guns. Some made a lot of difference, some a little, while others could be made equally well with original parts and some tuning.
This is one case to just save your money, as little as they cost to begin with. Actually, save yourself the aggravation of R&R the hammer spring just to get to this.
I took seven readings before doing a thing. They varied from7.5 to 6.75 lbs of pull; mostly 7.5. After going through the whole mess, then lubing everything again, I got the same readings. Mostly 7.5 lbs. What a disappointment!!
The worst part of it all is that this was replacing a spring out of a DPMS lower parts kit, so pretty bottom of the barrel to begin with.
OTOH, the included disconnector spring seems to tighter. It is definitely a little shorter though; not by much.
Good bang for the buck(02/07/2017)
Have used these on a few lowers. I start out with a Critical Capabilities LPK with ELG trigger. Pull weight is reduced and with some polishing on the trigger and hammer engagement surfaces I was able to get a very nice smooth pull between 4.5 and 6 lbs, (avg 5.25 lbs) with no loss of reliability on hard primers.,