45™ HEAVY DUTY EJECTOR

879971007369 100005999

Hardened, Machined Stainless Steel To Resist Wear & Breakage

Replacement for factory ejector is precision machined from hardened 416 stainless steel billet for extra strength and wear resistance. Helps ensure positive, consistent ejection, with reduced risk of reliability problems caused by a worn or broken ejector. Includes 416 stainless steel mounting screw.

SPECS: 416 stainless steel, natural finish. Fits Ruger Mark I, Mark II, Mark III, and 22/45 pistols.

Altro...

Acciaio Inossidabile Lavorato e Indurito per Resistere all'Usura e alla Rottura

Sostituto dell'espulsore di fabbrica, lavorato con precisione da un blocco di acciaio inossidabile 416 indurito per maggiore resistenza e resistenza all'usura. Garantisce un'eiezione positiva e coerente, riducendo il rischio di problemi di affidabilità causati da un espulsore usurato o rotto. Include vite di montaggio in acciaio inossidabile 416.

SPECIFICHE: Acciaio inossidabile 416, finitura naturale. Compatibile con le pistole Ruger Mark I, Mark II, Mark III e 22/45.

Altro...

Punteggi dei clienti per TACTICAL SOLUTIONS, LLC RUGER® .22 PISTOL EJECTOR

Numero di punteggi: 5
Da brownells.com: 5
Punteggio medio: 3,4

Works great in my older MKI Bull barrel (17/10/2011)

Had to take my time removing loose rivet on the old ejector but the results were worth it.
Ejector fit great and required no modification.
I used a 4-40 SS socket head cap screw to install it.
I used a non-permanent thread locker product to hold the screw.
I also ordered the same manufacturers extractor kit which is as impressive as this part.
Both are working well after 500+ rounds.

Not a drop in part for a Mark II 22/45 (18/05/2015)

My Mark II 22/45 needed a new ejector as the original one has become loose and causing frequent malfunctions. I looked at this part thinking it would be convenient as a screw would be easier than dealing a rivet.

The new ejector looks exactly as pictured on the website. Unfortunately it is wider than the factory piece. This means it wouldn't sit flush against the bottom/inside of the upper which is round; preventing the screw from reaching the ejector (more on this later). I had to grind off the base of the ejector to allow it to sit flush against the upper.

Once that was done, I realized the mounting hole on the ejector didn't even line up to the hole on the upper. More grinding on the little tab fixed that. Now that everything looks good to go, I put a little dab of blue Loctite on the provided screw, and figured I was about done.

I reassembled the pistol and manually cycled the pistol to function test and realized the ejector was loose. Took the gun apart and realized the provided screw is too short and only several threads were screwed into the ejector. Just manually cycling the gun easily loosened the screw.

A trip to Home Depot I was able to source a longer stainless steel screw. It seems to cycle fine by hand although I haven't had a chance to actually shoot it and see if the ejection problems have been solved.

<img width="500" src='/userdocs/reviewimages/d13345c0-ecc2-40cb-a925-e49e28c9ef63.jpg' alt=''>

<img width="500" src='/userdocs/reviewimages/d0c20264-861b-46f3-9c51-ea2463fe7ce2.jpg' alt=''>

<img width="500" src='/userdocs/reviewimages/d64ea1f7-d77b-43f8-9bb5-19769840480c.jpg' alt=''>

Not an exact fit and screw too short (22/06/2015)

I tried to install on a Ruger Mark 2 Competition model. Found that the supplied screw just touches the ejector, so will not screw in. Need at least a 1/4 inch length screw. Also, the mounting hole on the ejector does not line up to the hole on the upper. Will required me to find an appropriate screw and some fitting. Emailed the manufacture, did not reply.

Well Made, but Screw too short. (13/07/2015)

Because I didn't want to pay shipping costs and possible repair costs to have a new Ejector installed on my Ruger MK II, I decided to try this for myself. I rec'd it quickly and noticed that in deed, it needed fitting. OK! I ground it down (dremel) to proper shape. Then noticed the screw is much too short! Another reviewer said, get 4-40 size screw (about 2 dollars from Lowes), which I did. I then ground the screw down to an appropriate length. (Screw can not extend through Ejector into the upper-receiver.) So over all, good ejector, and unless manufacturer updates the supplied screw to a longer length, you will need to buy a longer screw. Still glad I did this.

.22 ejctor (30/10/2017)

great ejector

Leggi più recensioni su brownells.com

59.9 59.9 1 EUR

N. prodotto: 100005999
TACTICAL SOLUTIONS, LLC RUGER® .22 PISTOL EJECTOR
Parti Fabbricante: FP04X06 879971007369 Sostituto dell'espulsore di fabbrica, lavorato con precisione da un blocco di acciaio inossidabile 416 indurito per maggiore resistenza e resistenza all'usura. Garantisce un'eiezione positiva e coerente, riducendo il rischio di problemi di affidabilità causati da un espulsore usurato o rotto. Include vite di montaggio in acciaio inossidabile 416.

59.9 EUR 5 59,90 € *

Tempi di consegna circa 12-16 giorni.
5 pz. nel magazzino USA

Caratteristiche: Adatto per: Ruger Calibro: 22 Calibro (.223-.224) Finitura: Acciaio inox Modello: Mark III, Mark I, Mark II, 22/45

Aggiungi alla lista degli acquisti

Domande

Dettagli

Aggiungi alla lista degli acquisti

Domande

Top takeaways

Espulsore sostitutivo lavorato con precisione da acciaio inossidabile 416 per maggiore resistenza e durata.
Garantisce un'eiezione positiva e coerente, riducendo il rischio di problemi di affidabilità.
Compatibile con le pistole Ruger Mark I, Mark II, Mark III e 22/45; include vite di montaggio in acciaio inossidabile 416.

Caratteristiche

Adatto per: Ruger Calibro: 22 Calibro (.223-.224) Finitura: Acciaio inox Modello: 22/45,Mark I,Mark II,Mark III Peso della spedizione: 0,005kg Altezza di spedizione: 36mm Larghezza di spedizione: 69mm Lunghezza di spedizione: 94mm UPC : 879971007369