Tutti i prezzi sono comprensivi di Iva e oneri di importazione. Sono esclusi i costi di spedizione che verranno indicati nella procedura d'ordine.
P.IVA C.F. IT02801420981
N. prodotto: 749011485
N. fab.: 0910250
050806111325 Gli inserti per Bump Gage Sinclair vengono utilizzati per misurare la quantità di spinta della spalla durante l'impostazione dei dies di dimensionamento a lunghezza completa. I nostri Bump Gages si installano in uno dei nostri corpi comparatori e sono lavorati per adattarsi a particolari angoli di spalla delle cartucce. Piuttosto che misurare sulla linea di riferimento, questi gages indicano dalla spalla del bossolo per ottenere una misura migliore e più facilmente valutabile di quanto stai effettivamente dimensionando i tuoi bossoli. Di solito raccomandiamo tra .001" e .002" di spinta per fucili a otturatore e tra .003" e .005" per fucili tipo AR-15. È anche uno strumento utile per mantenere separati i tuoi bossoli e le munizioni caricate se possiedi più fucili camerati per la stessa cartuccia e per controllare le munizioni caricate.
In magazzino
Tempi di consegna circa 12-16 giorni. Più di 10 pz. nel magazzino USA
Tempi di consegna circa 12-16 giorni. Più di 10 pz. nel magazzino USA
Sinclair Bump Gage Inserts are used to measure the amount of shoulder bump when setting up full length sizing dies. Our Bump Gages install in either of our comparator bodies and are machined to fit particular shoulder angles of cartridges. Rather than measuring to the datum line, these gages indicate off of the shoulder of the case to get a better, more easily assessable measurement of how much you are actually sizing your cases. We usually recommend between .001" to .002" bump for bolt action rifles and between .003" and .005" for AR-15 type rifles. Also a useful tool for keeping your brass and loaded ammunition separated if you have multiple rifles chambered for the same cartridge and checking loaded ammunition.
Gli inserti per Bump Gage Sinclair vengono utilizzati per misurare la quantità di spinta della spalla durante l'impostazione dei dies di dimensionamento a lunghezza completa. I nostri Bump Gages si installano in uno dei nostri corpi comparatori e sono lavorati per adattarsi a particolari angoli di spalla delle cartucce. Piuttosto che misurare sulla linea di riferimento, questi gages indicano dalla spalla del bossolo per ottenere una misura migliore e più facilmente valutabile di quanto stai effettivamente dimensionando i tuoi bossoli. Di solito raccomandiamo tra .001" e .002" di spinta per fucili a otturatore e tra .003" e .005" per fucili tipo AR-15. È anche uno strumento utile per mantenere separati i tuoi bossoli e le munizioni caricate se possiedi più fucili camerati per la stessa cartuccia e per controllare le munizioni caricate.
Top takeaways
Gli inserti Sinclair Bump Gage misurano lo spostamento della spalla durante l'impostazione delle matrici di dimensionamento a lunghezza completa.
Si installano in corpi comparatori e si adattano agli angoli specifici delle spalle delle cartucce per una misurazione chiara e facilmente valutabile.
Raccomandati per fucili a otturatore girevole (.001"-.002") e fucili tipo AR-15 (.003"-.005"), utili anche per mantenere separate ottone e munizioni caricate.
Caratteristiche
Cartuccia:300 Winchester Magnum,6.5 x 55 mm Swedish Mauser,225 Winchester,30 Remington AR,7 mm STW,264 Winchester Magnum,8 mm Remington Mag,7 mm Remington Magnum,338 Winchester Magnum
Peso della spedizione:0,023kg
Larghezza di spedizione:83mm
Lunghezza di spedizione:146mm
UPC:050806111325
Dettagli dell'elemento
Made in Usa
Recensioni dei clienti
Valutazioni dei clienti (17)
3,1 / 5
Non raccomandato
Does not work for 6.5 Creedmoor 24/07/2018
Bought this 30A to check bumping the shoulders of my 6.5 Creedmoor brass. Had been using a Wilson Case gage to do the job and it works well I thought this may be faster. I bumped and bumped no reading beyond the initial cal of 1.501 on the digital calipers. Each bump i got a new reading on the Wilson Case Gage. Highly disappointed with the purchase.
Assolutamente raccomandato
Quality 20/06/2018
I have the original Stoney Point tool and this fits and works well on .338 Lapua Magnum cases to adjust the amount of shoulder bump on cases.
Più o meno raccomandato
Nicely machined doesnât fit without mods 18/04/2018
Iâm using this to measure shoulder bump between fired and full length sized cases. The âthrough holeâ is much too tight on all the 223 fires cases Iâve tried, this leads to cases sticking and readings of .010+ greater than normal. I can neck size to get them to fit but this is an additional step that Iâd prefer not to do, and is impossible to accomplish if Iâm trying to get data while on the range. I asked Sinclairâs techs if there was an issue with the product and they told me to ream it out with a drill bit. Not exactly the answer I was looking for. I would like to keep using this product because I like that the opening matches up with the shoulder angle unlike competing products, but it doesnât work out of the box.
Non raccomandato
Poor / Inaccurate Description 03/03/2018
Does NOT fit 300 Blackout without modification.
Non raccomandato
Incorrect fitment 24/02/2018
The details on this part say this fits 300 Blackout. Turns out it doesn't unless you modify it does not explain that anywhere in the description.
Più o meno raccomandato
Feels Like Plastic 26/01/2017
I thought the product was made of metal, which is should be. Feels like plastic, which it should not be. I didn't have much luck with this product and the inserts using it as a bump gauge. The readings were inconsistent even with two different calipers. Even trying to bump .308 cases back 4/1000ths for an AR10 was nearly impossible to do with any consistency. The finished products did not shoot as well as a fully resized cases in the testing I did.
Non raccomandato
Only works with certain calipers 13/12/2016
We use Aero Space brand calipers at the EPA. The slot on these arent wide enough to fit over them. That's OK but Sinclair should list some models they work with OR the width of the slot.
Assolutamente raccomandato
Quality Construction 18/07/2016
The bump gauge/comparator body has quality construction, and hold the inserts well. They attach to my calipers securely, and work well.
Assolutamente raccomandato
great product 01/03/2016
I really like the insert it's made of Stainless Steel so it will not wear easy . The gauge is also very easy to use, works on my Hornady body too.
Non raccomandato
Does not work for .416 Rigby 25/01/2015
The .416 Rigby is a beltless cartridge that headspaces on its ample 45 degree shoulder. This bump gage hole diameter is too small to host the outside dimensions of the .416 Rigby brass. It would have been nice to know there was a size limit on the exterior brass dimensions so as to avoid a return.
Assolutamente raccomandato
These Fit the Hornady Tools 07/01/2015
This little item told me right away what problem My sons hand loads had very easy to use and the fact they fit the Hornady tools that look like this is a big plus....If you already have the Hornady gauges.
Più o meno raccomandato
Requires honing geometry change 24/01/2014
The tapered opening is right at .277 and goes extremely far down VLD type/Accubond bullets, this makes it impossible to measure Ogive Combined Overall Length on loaded bullets. The older stainless steel hexagonal shaped comparator is much more useful as it's tapered opening is at .268". This comparator insert's tapered opening should start at .270" within .001" of that.
Assolutamente raccomandato
Great tool for measuring shoulder bump 13/12/2013
I bought this tool to use with the Sinclair XL Comparator body and it works great! I am able to measure the distance between the should and the base of a fire cartridge and then set my sizing die to bump the shoulder back a certain distance. I would definitely buy this tool again.
Assolutamente raccomandato
Great tool for measuring bullets/cases 13/12/2013
I bought this tool in order to measure bullets from the ojive to the base and also to measure should bump. It's a high quality tool and works perfectly for my needs. Being that it's the XL version, you're able to measure shoulders with a bullets installed.
Non raccomandato
Poor discription 02/07/2012
It's listed as "30-06 Family" but will not work with 17deg shoulders over 338 cal.
Assolutamente raccomandato
Much Better than Hornady LNL inserts 23/02/2011
It's much easier to measure headspace with an insert that's tapered to match the cartridge's shoulder angle. Easier to use than the 90 deg. edge of the straight hole drilled in the original Hornady LNL inserts.
Assolutamente raccomandato
Keep it simple 09/02/2011
Simplicity is more often than not the best way to do things...This product is so simple but is something every shooter should have at their reloading bench. Use it every few hundred rounds to make sure your desired bullet jump matches wear in barrel.
Operatore economico responsabile secondo il regolamento UE
Brownells
Via Mezzavilla 4
25043 Breno
Italia
service@brownells.it
Ultimi visualizzati
Ops! Qualcosa è andato storto.
Si è verificato un errore durante il caricamento di questo contenuto. Aggiorna la pagina per continuare. Se il problema persiste, contatta il nostro servizio clienti.
*
Tutti i prezzi sono comprensivi di Iva e oneri di importazione. Sono esclusi i costi di spedizione che verranno indicati nella procedura d'ordine.
Misura con precisione la spalla delle cartucce con l'inserto Bump Gage SINCLAIR #25. Strumento essenziale per i tuoi progetti di ricarica! 🔧
Gli inserti Sinclair Bullet Comparator sono in acciaio inossidabile e progettati per replicare accuratamente la gola della camera.
Consentono di misurare e confrontare rapidamente la distanza ogiva-base del proiettile e del cartuccia caricata.
Forniscono risultati più consistenti rispetto alla misurazione delle lunghezze totali, eliminando le variazioni del meplat.
I mandrini espansori in acciaio inossidabile Sinclair International sono realizzati con precisione per garantire una finitura di alta qualità.
Sono compatibili con gli strumenti di tornitura del collo NT-3000 e NT-1000, oltre che con modelli più datati.
I mandrini espansori sono realizzati .001" più grandi dei mandrini di tornitura, migliorando la precisione e la semplicità del processo di tornitura del collo.
Il Comparator Sinclair è ideale per ordinare i proiettili in base alla lunghezza dalla base, utile per rifilare il meplat.
Si attacca alla lama del calibro e utilizza inserti specifici in acciaio inossidabile per ogni calibro, dal 17 al 45.
Gli inserti sono compatibili con i corpi comparatori Sinclair e Stoney Point più vecchi, ma non sono adatti per misurare cartucce corte.
I mandrini Sinclair in acciaio inossidabile per tornitura del collo sono dimensionati 0,002 pollici in meno del diametro del proiettile.
Realizzati con alta precisione, garantiscono tolleranze strette e consistenti regolazioni sugli strumenti di tornitura NT-4000 e NT-5000.
Adatti per cartucce dal calibro 17 al 50, con mandrini di grande calibro che si adattano solo al corpo espansore per grandi calibri.
Il Sinclair Bullet Checker Stand permette di ordinare i proiettili per lunghezza dalla base all'ogiva con precisione.
La base in granito nero è stabile e piatta, garantendo fermezza sul banco di caricamento.
L'indicatore a quadrante incluso facilita l'inserimento e la rimozione dei proiettili nei comparatori, venduti separatamente in vari calibri.