Precisely aligns individual steel stamps to help ensure characters are straight and evenly spaced when stamping caliber designations on barrels. Allen head screws allow adjustment for accurate character spacing, so you get truly professional looking results. Machined port allows an unobstructed view of the first stamp head to ensure correct positioning on workpiece prior to tapping with your hammer. Accepts ¼" square stamps with 1/16", 3/32", or 1/8" character sizes. Fits barrels up to 1-3/8" diameter.
SPECS: Aluminum, natural finish with steel U-bolt and hardware. 2-3⁄8" (6cm) long x 3¼ (8.2cm) wide, 1½ (3.8cm) high.
Altro...
Per un Allineamento Preciso Durante la Marcatura dei Fucili
Allinea con precisione i timbri in acciaio individuali per garantire che i caratteri siano dritti e equidistanti quando si marcano le designazioni del calibro sui fucili. Viti a testa esagonale consentono la regolazione per uno spaziamento accurato dei caratteri, ottenendo così risultati dall'aspetto veramente professionale. Una porta lavorata consente una visione non ostruita della testa del primo timbro per assicurare un posizionamento corretto sul pezzo da lavorare prima di battere con il martello. Accetta timbri quadrati di ¼" con dimensioni dei caratteri di 1/16", 3/32" o 1/8". Adatto per fucili con diametro fino a 1-3/8".
SPECIFICHE: Alluminio, finitura naturale con U-bolt in acciaio e hardware. Lunghezza 2-3⁄8" (6cm) x larghezza 3¼ (8.2cm), altezza 1½ (3.8cm).
Altro...
Punteggi dei clienti per LA BOUNTY STEEL STAMP GUIDE
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 1
Caution(08/01/2010)
The device is well made, however it will slip resulting in uneven markings. After reading the instructions over several times I tried it. I was disappointed with the results. I then tried it again on an old barrel and the same thing happened again. I made sure the holding ring was very tight. My opinion is save your maoney and go to a jeweler of plaque company that can do it right, the first time.
warning - disapointed(06/12/2012)
I was not able to get this device to work well even when following the directions. In the end, I was able to load several stamps in a row then tighten up the guide and clamp the assembly to a barrel. Even this way, it was hard to use. The clearance between the plates was too tight to insert the stamps without loosening the side screws. It is hard to get just five stamps into the guide (e.g., 300H&H cannot be done without the alignment risk of a second setup). I wish I had read keydiverfla's review before laying down my money.
N. prodotto: 521104000 LA BOUNTY STEEL STAMP GUIDE Parti Fabbricante: NONE Allinea con precisione i timbri in acciaio individuali per garantire che i caratteri siano dritti e equidistanti quando si marcano le designazioni del calibro sui fucili. Viti a testa esagonale consentono la regolazione per uno spaziamento accurato dei caratteri, ottenendo così risultati dall'aspetto veramente professionale. Una porta lavorata consente una visione non ostruita della testa del primo timbro per assicurare un posizionamento corretto sul pezzo da lavorare prima di battere con il martello. Accetta timbri quadrati di ¼" con dimensioni dei caratteri di 1/16", 3/32" o 1/8". Adatto per fucili con diametro fino a 1-3/8".
79.9EUR379,90 €
*
Tempi di consegna circa 12-16 giorni. 3 pz. nel magazzino USA
Allinea con precisione i timbri in acciaio per marcature professionali su fucili, grazie alle viti a testa esagonale per la regolazione dei caratteri.
La porta lavorata permette una visione chiara del primo timbro, garantendo un posizionamento corretto prima della martellatura.
Compatibile con timbri quadrati di ¼" e caratteri di 1/16", 3/32" o 1/8", adatto per fucili con diametro fino a 1-3/8".
Caratteristiche
Peso della spedizione: 0,227kgAltezza di spedizione: 79mmLarghezza di spedizione: 84mmLunghezza di spedizione: 119mm
Dettagli dell'elemento
Made in Usa
Allinea con precisione i timbri in acciaio con la guida LA BOUNTY. Ottieni risultati professionali su fucili. Facile regolazione e visione chiara. 🛠️ Scopri di più!
Precisely aligns individual steel stamps to help ensure characters are straight and evenly spaced when stamping caliber designations on barrels. Allen head screws allow adjustment for accurate character spacing, so you get truly professional looking results. Machined port allows an unobstructed view of the first stamp head to ensure correct positioning on workpiece prior to tapping with your hammer. Accepts ¼" square stamps with 1/16", 3/32", or 1/8" character sizes. Fits barrels up to 1-3/8" diameter.
SPECS: Aluminum, natural finish with steel U-bolt and hardware. 2-3⁄8" (6cm) long x 3¼ (8.2cm) wide, 1½ (3.8cm) high.
Altro...
Per un Allineamento Preciso Durante la Marcatura dei Fucili
Allinea con precisione i timbri in acciaio individuali per garantire che i caratteri siano dritti e equidistanti quando si marcano le designazioni del calibro sui fucili. Viti a testa esagonale consentono la regolazione per uno spaziamento accurato dei caratteri, ottenendo così risultati dall'aspetto veramente professionale. Una porta lavorata consente una visione non ostruita della testa del primo timbro per assicurare un posizionamento corretto sul pezzo da lavorare prima di battere con il martello. Accetta timbri quadrati di ¼" con dimensioni dei caratteri di 1/16", 3/32" o 1/8". Adatto per fucili con diametro fino a 1-3/8".
SPECIFICHE: Alluminio, finitura naturale con U-bolt in acciaio e hardware. Lunghezza 2-3⁄8" (6cm) x larghezza 3¼ (8.2cm), altezza 1½ (3.8cm).
Altro...
Punteggi dei clienti per LA BOUNTY STEEL STAMP GUIDE
Numero di punteggi: 2
Da brownells.com: 2
Punteggio medio: 1
Caution(08/01/2010)
The device is well made, however it will slip resulting in uneven markings. After reading the instructions over several times I tried it. I was disappointed with the results. I then tried it again on an old barrel and the same thing happened again. I made sure the holding ring was very tight. My opinion is save your maoney and go to a jeweler of plaque company that can do it right, the first time.
warning - disapointed(06/12/2012)
I was not able to get this device to work well even when following the directions. In the end, I was able to load several stamps in a row then tighten up the guide and clamp the assembly to a barrel. Even this way, it was hard to use. The clearance between the plates was too tight to insert the stamps without loosening the side screws. It is hard to get just five stamps into the guide (e.g., 300H&H cannot be done without the alignment risk of a second setup). I wish I had read keydiverfla's review before laying down my money.